
Hanging proudly...Moderators: Greg B, Nnnnsic, Geoff, Glen, gstark, Moderators
Forum rules
Please note that image critiquing is a matter of give and take: if you post images for critique, and you then expect to receive criticism, then it is also reasonable, fair and appropriate that, in return, you post your critique of the images of other members here as a matter of courtesy. So please do offer your critique of the images of others; your opinion is important, and will help everyone here enjoy their visit to far greater extent. Also please note that, unless you state something to the contrary, other members might attempt to repost your image with their own post processing applied. We see this as an acceptable form of critique, but should you prefer that others not modify your work, this is perfectly ok, and you should state this, either within your post, or within your signature. Images posted here should conform with the general forum guidelines. Image sizes should not exceed 950 pixels along the largest side (height or width) and typically no more than four images per post or thread. Please also ensure that you have a meaningful location included in your profile. Please refer to the FAQ for details of what "meaningful" is.
Previous topic • Next topic
11 posts
• Page 1 of 1
Hanging proudly...This is not for critique but more to say if you have a print that u like..then frame it. The one on the right is my avatar image and I've been meaning to frame it for ages...here's the result. Yep - the image on the left isn't quite straight and it was my bday present to Bel - our local beach (I didn't photograph this one). The image on the right was printed on the R1800 at A3 size:
![]() Geoff
Special Moments Photography Nikon D700, 50mm 1.4, 85mm 1.4, 70-200 2.8VR, SB800 & some simple studio stuff.
They look good Geoff... I must admit that I am terrible when it comes to getting any of my images printed... I tend to print the family snapshots occasionally and nothing else...
The last thing I want to do is hurt you... but it's still on the list...
![]()
Matt - something I installed last year...I'm just on my way out the door, will post more about it later. Commonly used in art galleries etc.
Geoff
Special Moments Photography Nikon D700, 50mm 1.4, 85mm 1.4, 70-200 2.8VR, SB800 & some simple studio stuff.
I second this...
I finally, well actually Rick finally, finished the frames for the two 24x30 prints I got from Pixel Perfect. Whilst they are massive in our small house they look good and will look much better once we have a bigger space for them. It is nice to see some prints up on the wall again. Andrew
Nikon D3 and lot's of Nikon stuff!!
More info or link Geoff if possible.. Cheers MATT
Matt sorry for the delay.
This is the mob I used: http://www.fxhangingsystems.com.au/ Based in Balmain. I need to get some more clips etc for another wall in our unit soon actually. The system works very well. Installation is a little messy but done properly it looks neat and tidy. We had to drill into red brick, very noisy and lots of dust but the end result was worth it. I use the Locator (wall sytsem). Hope this helps. Geoff
Special Moments Photography Nikon D700, 50mm 1.4, 85mm 1.4, 70-200 2.8VR, SB800 & some simple studio stuff.
Geoff, how did you frame it? Did you let someone do it or you went for DIY?
I got couple of prints here sitting lonely without a frame... ![]()
the one on the right Yi-p...I got done professionally at a local framers - the one one the left I bought as is ![]() Geoff
Special Moments Photography Nikon D700, 50mm 1.4, 85mm 1.4, 70-200 2.8VR, SB800 & some simple studio stuff.
Previous topic • Next topic
11 posts
• Page 1 of 1
|